For Integration Projects

SGx Smart Seismic Sensor

SensoGuard detection, built into your system

A buried seismic sensor with SensoGuard's adaptive algorithms on a chip. It connects to your controller or device over UART TTL, RS485 or dry contact. Supplied for integration projects, with a minimum order quantity.

A Smart Sensor, Not an Analog One

Conventional seismic sensors send a raw signal and leave the analysis to someone else. SGx has SensoGuard's field-proven adaptive algorithms embedded on a chip, so it classifies each event itself and reports it to your controller, with sensitivity that can be adjusted per event.

It is built for IoT applications and for projects that run their own controller or device: you get SensoGuard's detection without adopting a full SensoGuard system.

Discuss a Project
SGx smart seismic sensor on its ground spike

Supplied for Projects

SGx is a component for integration projects, with a minimum order quantity. It is not sold for one-off or standalone use.

Device makers

Build seismic detection into your own product, through the interface it already has.

System integrators

Add buried detection to a project that runs on its own controller or platform.

Large projects

Projects that need the sensor inside their own architecture, at project quantities.

Need a complete system rather than a component? See the AIO wireless sensors, InvisiFence Plus or the MOSS kit.

How SGx Works

From a vibration in the ground to an event on your controller

1

Bury

The sensor goes in 20 to 50 cm deep on its spike. Plug and play, and maintenance free.

2

Classify

Footsteps, vehicles and digging send vibrations through the ground. The on-chip adaptive algorithm detects them all around the sensor and classifies the event.

3

Report

The sensor reports to your controller or device over UART TTL, RS485 or dry contact.

Two Models

The same interfaces and on-chip algorithm, at two detection ranges.

SGxSGx XR
FootstepsUp to 12m / 39ft radiusUp to 18m / 60ft radius
VehiclesUp to 25m / 82ft radiusUp to 35m / 115ft radius
DiggingUp to 25m / 82ft radiusUp to 35m / 115ft radius
Sensor size131 × 50 × 42mm95 × 70mm
Weight115g500g
InterfacesUART TTL, RS485, dry contactUART TTL, RS485, dry contact

Detection ranges are maximums. Actual range depends on soil and sensitivity settings.

Built to Integrate

Adaptive Algorithm

Event classification on the chip, with sensitivity adjustable per event.

Several Interfaces

UART TTL, RS485 or dry contact, to fit the controller you already use.

Ultra Low Power

About 1 mA at 3.3 V.

Plug and Play

Simple installation, maintenance free.

Built for the Ground

IP68 (MIL-STD 810G), -40°C to 85°C.

RoHS Compliant

Ready for products that must meet RoHS.

Technical Details

Specifications from the SGx and SGx XR datasheets.

SGx sensor

Detection Capabilities

Footsteps DetectionUp to 12m / 39ft radius
Vehicle DetectionUp to 25m / 82ft radius
Digging DetectionUp to 25m / 82ft radius
Detection Zone360° coverage

Integration & Interface

InterfacesUART TTL, RS485 and Dry Contact
Power Consumption~1mA @ 3.3V

Environmental

IP RatingIP68 (MIL-STD 810G)
Operating Temperature-40°C to 85°C / -40°F to 185°F
ComplianceRoHS

Physical Specifications

Dimensions (Sensor)131mm × 50mm × 42mm / 5.1″ × 1.96″ × 1.65″
Dimensions (Spike)55mm / 2.16″
Weight115g / 0.2lbs
Installation Depth20-50cm / 7.5″-19″
SGx XR sensor

Detection Capabilities

Footsteps DetectionUp to 18m / 60ft radius
Vehicle DetectionUp to 35m / 115ft radius
Digging DetectionUp to 35m / 115ft radius
Detection Zone360° coverage

Integration & Interface

InterfacesUART TTL, RS485 and Dry Contact
Power Consumption~1mA @ 3.3V

Environmental

IP RatingIP68 (MIL-STD 810G)
Operating Temperature-40°C to 85°C / -40°F to 185°F
ComplianceRoHS

Physical Specifications

Dimensions (Sensor)95mm x 70mm / 3.74″ x 2.7″
Dimensions (Spike)75mm / 2.95″
Weight500g / 1.1lbs
Installation Depth20-50cm / 7.5″-19″

Planning a Project with SGx?

Tell us what SGx will go into. We'll reply with the integration details, the minimum order quantity and a quote.

Frequently Asked Questions

Seismic sensors buried underground SensoGuard seismic sensor on its ground spike

Questions about integrating SGx? Here are the ones we hear most.

What is SGx?

SGx is a buried smart seismic sensor for integration into third-party controllers and devices. SensoGuard's field-proven adaptive algorithms run on a chip inside the sensor, so it classifies each event itself and reports it over UART TTL, RS485 or dry contact.

Can I buy a few SGx sensors for my own site?

SGx is supplied for integration projects, with a minimum order quantity. It is not sold for one-off or standalone use. For a ready-to-run system, see the AIO wireless sensors, InvisiFence Plus or the MOSS kit.

How does SGx connect to my system?

Through UART TTL, RS485 or a dry contact, whichever your controller or device uses. Tell us about your system and we'll send the integration details.

What is the difference between SGx and SGx XR?

Range and housing. SGx detects footsteps up to 12 m and vehicles or digging up to 25 m, in a 131 × 50 × 42 mm, 115 g sensor. SGx XR detects footsteps up to 18 m and vehicles or digging up to 35 m, in a 95 × 70 mm, 500 g sensor. Both cover 360° and use the same interfaces.

How is SGx installed?

It is buried 20 to 50 cm deep on its spike. It is plug and play and maintenance free, and its sensitivity can be adjusted per event.

How much power does SGx use?

About 1 mA at 3.3 V.

Technical Documents

Download the datasheets for SGx and SGx XR.

SGx Technical Specification

PDF Document

SGx XR Technical Specification

PDF Document